- Length of an Engineer’s chain is :
- 100 ft
- 66 ft
- 20 m
- 33 ft
Ans:- A
- The most accurate tape is :
- Linen tape
- Inver tape
- Steel tape
- Metallic tape
Ans:-B
- Identify an instrument used for marking stations :
- Chain
- Tape
- Peg
- Cross staff
Ans:-C
- Least count of a leveling staff :
- 5 cm
- 5 m
- 1 mm
- 5 mm
Ans:-D
- The line passing through the optical centre of the objective traversing the eye pice and entering the eye is known as :
- Line of sight
- Line of collimation
- Optical centre of a lens
- Axis of the telescope
Ans:- A
- The first sight taken on a leveling staff held at a point of known elevation is called :
- S
- S
- I
- S
Ans:-B
- The scale on which three dimensions can be measured known as :
- Chord scale
- Plain scale
- Diagonal scale
- None of the above
Ans:- C
- A triangle is said to be well conditioned if none of the angles is less than :
- 90 0
- 60 0
- 45 0
- 30 0
Ans:- D
- A line joining some fixed points on the main survey lines :
- Tie line
- Check line
- Base line
- None of the above
Ans:- A
- Equidistant and parallel contours represent__________ areas.
- Flat
- Gentle slope
- Steep slope
- Slope
Ans:-B
- The vertical distance between any two consecutive contours is called :
- Vertical equivalent
- Horizontal equivalent
- Contour interval
- Contour gradient
Ans:-C
- If R.L. of a B.M. is 200.000 m, back sight is 1.525 m and fore sight is 3.285 m. R.L. of the forward station is :
- 700 m
- 525 m
- 810 m
- 249 m
Ans:- D
- Rocks formed by cooling of magma is :
- Metamorphic rocks
- Igneous rocks
- Sedimentary rocks
- None of the above
Ans:-B
- Slate in the form of tiles is used :
- For paving
- As road metal
- As an excellent roof covering material
- None of the above
Ans:-C
- An example for silicious rock is :
- Marble
- Slate
- Lime stone
- Sand stone
Ans:- D
- Heaviness of a stone is indicated by its :
- Specific gravity
- Resistance to abrasive force
- To withstand stresses due to vibrations
- Resistance to compressive force
Ans:-A
- Type of stone for electrical switch boards :
- Granite
- Gneiss
- Marble
- Lime stone
Ans:-C
- The heating of lime stone to redness without contact with air or in absence of air is known as :
- Oxidation
- Burning
- Carbonization
- Calcinations
Ans:- D
- The constituent which makes the brick earth plastic and tends the brick to hardness :
- Silica
- Clay
- Lime
- Iron oxide
Ans:-B
- For one cubic metre of brick masonry the number of bricks required are :
- 500
- 400
- 450
- 550
Ans:-A
- The approximate weight of a brick should be :
- 2 kg
- 5 kg
- 0 kg
- 5 kg
Ans:- A
- The chemical reaction between cement and water is called :
- Consistency
- Soundness
- Hydration
- Setting time
Ans:-C
- The soundness of cement is tested by :
- Vicat’s apparatus
- Sieve analysis
- Slump test
- Le-Chatelier apparatus
Ans:-D
- The specific surface of a good Portland cement should not be less than :
- 3200 cm2/gm
- 2250 cm2/gm
- 1100 cm2/gm
- 500 cm2/gm
Ans:- B
- Cement used for dam, retaining wall construction etc is :
- Ordinary Portland cement
- Rapid hardening cement
- Low heat cement
- Air entrained cement
Ans:-C
- A plant having neither leaves nor flowers. This is due to
- Fungus
- Chemical decay
- White rots
- Termites
Ans:-A
- The horizontal thin fibrous tissues which extended radially from pith towards cambium or from cambium towards the pith is called :
- Sap wood
- Medullary rays
- Outer Bark
- Annual rings
Ans:- B
- The type of defect of timber which separates the whole or part of one annual ring from another is :
- Heart shakes
- Star shakes
- Radial shakes
- Cup shakes
Ans:-D
- Which one is not a method of preservation of timber?
- Curing
- Tarring
- Charring
- creosoting
Ans:-A
- The seasoning of timber is done to:
- Heat the timber
- Expel the moisture
- Make it water proof
- Increase its strength
Ans:-B
- If knotting is not properly done resins from knots spoils the point. It is called :
- Chalking
- Scaling
- Exudation
- Wrinkling
Ans:-C
- The liquid part of a paint is called:
- Pigment
- Solvent
- Driver
- Vehicle
Ans:-D
- The volatile dilutent added to a paint is known as :
- Driver
- Pigment
- Solvent
- Thinner
Ans:-D
- The steel used in RCC :
- Cast iron
- Stainless steel
- Mild steel
- Chromium steel
Ans:-C
- Coating the surface of steel by thin layer of zinc is known as :
- Normalizing
- Galvanizing
- Spraying
- Heating
Ans:-B
- Glass made of several layers of plate glass and alternate layers consists of Vinyl-resin plastic is :
- Bullet proof glass
- Block glass
- Fiber glass
- Flint glass
Ans:-A
- Initial setting time of rapid hardening cement should not be less than :
- 45 minutes
- 15 minutes
- 30 minutes
- 60 minutes
Ans:-C
- The maximum size of aggregates particles recommended for beams, columns etc is :
- 80 mm
- 40 mm
- 10 mm
- 20 mm
Ans:- D
- Continuous strain with time which the concrete structure undergone due to application of a external load is :
- Workability
- Creep
- Bleeding
- Segregation
Ans:- B
- M20 concrete is :
- 1 : 1 ½ : 3
- 1 : 2 : 4
- 1 : 3 : 6
- 1 : 5 : 10
Ans:- A
- The slump value required for road construction :
- 40 to 50 mm
- 20 to 40 mm
- 70 to 80 mm
- 80 to 150 mm
Ans:-B
- The course of a masonry provided at ceiling level of the roof projecting outside the surface of the wall of the building :
- String course
- Corbel
- Cornice
- Block-in-course
Ans:- C
- Rubble masonry used for the construction of low boundary walls of ordinary houses :
- Random Rubble masonry
- Coursed Rubble masonry
- Dry Rubble masonry
- Un-coursed Rubble masonry
Ans:-D
- A brick laid with its length parallel to the face or front or direction of a wall is called :
- Stretcher
- Header
- Bed
- Closer
Ans:-A
- In brick masonry, the frog of the brick is normally kept on the :
- Interior
- Exposed face
- Top face
- Bottom face
Ans:-C
- The vertical joints between bricks in longitudinal cross directions are known as :
- Cross joint
- Hearting
- Bed joints
- Perpend
Ans:-D
- A component part of a scaffolding which are the horizontal members parallel to the wall:
- Ledgers
- Putlog
- Transoms
- Braces
Ans:-A
- Temporary support to the structures is called :
- Foundation
- Shoring
- Scaffolding
- Underpinning
Ans:-B
- The wedge shaped units forming the courses of an arch :
- Skewback
- Voussoir
- Crown
- Key
Ans:-B
- Type of arch consists of two curves which are meeting at the apex of a triangle is called :
- Inverted arch
- Flat arch
- Segmental arch
- Pointed arch
Ans:- D
♦ Important Links (महत्वाच्या लिंक्स) ♦
〉 Government Jobs.
〉 Private Jobs.
〉 सर्व परीक्षांच्या सराव प्रश्नपत्रिका (Previous Question Papers).
〉 परीक्षेचे निकाल (Results).
〉 परीक्षा प्रवेशपत्र (Hall Tickets).
〉 MPSC भरती.
〉 Bank Jobs.
〉 Mega Bharti.
〉 Current Affairs ((चालू घडामोडी).
〉 रोजगार मेळावा (Jobs Fairs).
🔎जिल्हा नुसार जाहिराती📲 |
|||||
अहमदनगर | अकोला | अमरावती | औरंगाबाद | भंडारा | बुलढाणा |
चंद्रपुर | धुले | गढ़चिरौली | गोंदिया | हिंगोली | जलगांव |
जालना | कोल्हापुर | लातूर | मुंबई | नागपुर | नांदेड़ |
नंदुरबार | नाशिक | उस्मानाबाद | पालघर | परभानी | पुणे |
रायगढ़ | रत्नागिरि | सांगली | सातारा | सिंधुदुर्ग | सोलापुर |
ठाणे | वर्धा | वाशिम | यवतमाल | बीड |
🎓शिक्षणानुसार जाहिराती💼 |
|||||
७ वी (7th) | दहावी (SSC) | बारावी (HSC) | डिप्लोमा | आय.टी.आय | पदवी |
पदव्युत्तर शिक्षण | बी.एड | एम.एड | एल.एल.बी / एल.एल.एम | बीएससी | एमबीए |
बीसीए | एमसीए | बी.कॉम | एम.कॉम | GNM/ANM | एमएससी |
बी.फार्म | एम.फार्म | बी.ई | एम.ई | BAMS/BHMS | एम.बी.बी.एस / एम.डी |
बी.टेक | एम.टेक | MS-CIT |